700mm on Infrared and UV

infrared heating tube ir tungsten halogen lamp 700mm 220v 1500w

Thu, 23 Jul 2026 02:41:37 +0800

Let’s talk about the 700mm Tungsten Halogen Lamp

When you need heat—and you need it now—these 1500W tubes are exactly what you’re looking for. We built them for those high-pressure industrial drying and curing lines where you can’t afford to wait around for things to warm up. At 700mm long and running on 220V, they hit that sweet spot. They’re powerful enough to get the job done, but they don’t take up your entire shop floor. The guts of the thing The real magic is in the tungsten filament. It gets scorching hot almost instantly. Instead of just warming the surface of your material, it puts out short-wave infrared radiation that actually sinks deep inside. It’s the difference between a warm breeze and a heat lamp that actually penetrates. And since it runs on 220V, you can just plug it into most industrial grids. No need to mess around with bulky, annoying step-down transformers. Why it doesn’t just burn out Normally, tungsten likes to evaporate and gunk up the glass, which kills your heat output. We fixed that with a halogen gas fill. It basically scrubs the tube clean as it works, so the lamp stays clear and the wattage stays steady. We also used quartz glass. Why? Because these things take a beating. You can flip the power on and off all day long and the glass won’t crack from the thermal shock. Just a heads-up: make sure your mounting brackets aren’t squeezing the glass too tight, or you’re asking for trouble. A few things to watch out for If you’re swapping out an old mid-sized IR heater, this should slide right in. But here’s the thing: 1500W is a lot of energy in a small space. Check your reflectors. If they’re warped or dusty, you’re basically throwing heat away. Also, be careful with your conveyor speed. This lamp is fast.**Really fast.**If your parts move too slowly, you’ll end up scorching your materials. Make sure your control system can switch quickly so you don’t accidentally cook your workpiece.

Halogen Lamp Replacement Parts 700mm 230v 1200w

Mon, 20 Jul 2026 02:26:32 +0800

Let’s talk about our 700mm Halogen Lamps

If you need a massive burst of infrared heat—and you need it now—these lamps are your best bet. We built them specifically for those high-pressure spots like industrial ovens or curing lines where you can’t afford to wait around for things to warm up. The power side of things Here is the deal with the specs: these are 1200W at 230V. We landed on that specific wattage because it gives you a steady, reliable heat profile across the whole 700mm length. But a quick heads-up: don’t cut corners with your power supply. If your voltage is jumping all over the place, you’re going to fry the filament way sooner than you should. Keep that 230V steady, and the lamps will do their job. Why quartz and halogen? We use high-purity quartz for the tubes. Inside, there’s a halogen gas that does the heavy lifting. It stops the tungsten filament from evaporating and gunking up the glass. That’s a big deal. It means the glass stays crystal clear, and the heat keeps hitting your target just as hard on day 100 as it did on day one. Plus, we used standard end-caps. You just pop them into your existing sockets and you’re good to go. No need to go hacking away at your machine frame. Putting them to work You’ll mostly see these in PET blowing, plastic welding, or drying paint. The best part? The ramp-up is almost instant. You hit your target temperature in seconds. It’s fast. Really fast. Just keep one thing in mind. All that power in a 700mm tube creates a ton of radiant heat. If your reflectors are dirty or pitted, you’re wasting energy and risking a meltdown in your housing. Keep those reflectors polished. And every 500 hours or so, take a peek at the contact points. If you see oxidation, clean it off so you don’t deal with any nasty arcing at the terminals.

700mm 1200w Replacement Halogen PET blowing machine

Thu, 02 Jul 2026 01:12:08 +0800

The 700mm, 1200W Halogen Lamp That Keeps Your PET Blowing Line Humming

We built this 700mm, 1200W halogen heating lamp to be the direct replacement your PET blowing machine is waiting for. Its one job? Deliver steady, intense heat to pre-warm PET preforms so they stretch evenly when it counts. If your old halogen tube finally gave up, this one slips right in. No machine modifications. No downtime headaches. Just get the line back up and running.